FAQ

For open area, diameter 4m/4.5m will be sufficient, because the wheelbase of most cars are about 3m. But at some limited space, 5m/5.5m is recommended, just make sure the the vehicle can all within turntable size.

The turntable rotating speed is 0-2rmp, which is adjustable.
For max speed, the 4.5m turntable can rotate approx 2 circles within 60 seconds, one 4m diameter turntable can rotate approx 2.5 circles within 1 minute. And one 6m turntable can rotate approx 1.8 circles within 1 minute.

Approx 25 seonds for 180 degree turntable, take 4.5m turntable for example.

Yes, there is a E-stop button both on control box and Remore control.

Yes, when power off, you can also rotate the turntable manually, but push hard.

Theoretically, we can use the remote within 50m, but we suggest to use the remote within 10m, because you may not see the turntable or surroundings clearly if too far.

Now we have carbon steel checker plate, Galvanized checker plate, aluminum checker plate, stainless steel checker plate, tempered glass, bricks, concrete and plywood.

Normally carbon steel checker plate, galvanized plate and aluminum checker plate are most popular used.

Yes, one turntable will come with 2pcs remote control.

If the site permits, we suggest you could make a 250mm pit, so the top platform can ne flushed with finished floor.

No problem, we have a floor mounted turntable, self height 180mm with around drive on ramp, you can install it on the finished floor directly without any concrete work.

We will provide 5-8m wires for control box, so you can place the control box approx 5-8m from turntable.ble will come with 2pcs remote control.

Sure, the turntable is ok for private use, single phase is also our standard power supply.

Sure, the turntable is ok for commercial use, so three phase is also ok.

Usually we need 20 working days for production.

Drawing confirmed, production drawing, materials parepared and cutted, welding, shot blasting, powder coating, electric box assembled, turntable assembled, turntable tested, packaged.

Yes, there are a slip ring at the middle bearing, we can make AC to platform possible easily.

Pit installation type, we have 250mm high standard; If floor mounted type, 180mm high.

We have two options:
1.  All around ramp beside the turntable.
2. Two pcs drive on ramp only, recommended due to lower cost and easy moved.

Yes, it has no any problem for pit installation turntable.
If floor mounted type, 1200mm length, 180mm high ramp is also no problem.

2000kg, 3000kg, 4000kg, and 5000kg are available for car turntable.

We adopts friction drive for car turntable, which is easier installation and cost effective.

We also use pin gear drive for heavy and big diameter rotating platform, that is more suitable.

Simpely, friction drive, suit for car turntable, diameter within 12m, capacity within 5000kg.
While pin gear drive, suit for heavy capacity, big diameter.

Different drive system suit for different applications, maybe suit for A, not for B.
So we cannot say which one is better, where is suitable, where is better

12 months warranty from installation, all the parts can be free sent during warranty.

If pit prepared well, 3 workers can install one unit within 4 hours.

For one standard 4m turntable, it cost usd5500-6500, the price may differs according to different top surface and capacity.

Yes, sure. The turntable is all fixed by bolts, so you can disassemble it after short time use.

It includes self height of car turntable, our standard size 250mm high.
And diameter of turntable, usually diameter 4m, 4.5m, 5m, which suit for most cars.

To choose a car turntable, you need to consider the factors below:
Budget, pit installation or floor mounted; indoor or outdoor use; Top surface; Ground clearance of your car if floor mounted.

No, the turntable are bolts fixed and connected.

Just one electric wrench, all structure are conneced by bolts, no any welding.

The notes here may not all pertain to your specific installation but the information should prove helpful in understanding the requirements and installation of the equipment.
We suggest to do the checking list every 3-6months.

1.Please be sure the wheels and rails are clean, or there will be noise during turntable running.

2.Kindly check if the control box wiring loosing or aging every 6 months.

3.Check if each auxiliary wheels working well, please note some auxiliary wheels may not touch the rails when empty turning due to the motor wheels support on the rails, it is normal, and auxiliary wheel will also touch on the rails when car loading.

4.Check if each motor working condition, not vibrative or noisy, check every 6 months.

5.Check if the bolts on structure or platform loose or not, please tighten the screws.

6.Check if the auxiliary wheels has any abrasion, please replace the new one for heavily abraded wheels.

Yes, we have the IP68 water-proof motor for outdoor use, it can also work in water and other dusty environments. But please clarify to the sales before order, because the motor of indoor use and outdoor use is a little dirrerent.